There's water pooling around the base of my hot water system. Is it serious?

It can be. A small amount of water from the pressure relief valve is normal during heating cycles, but steady pooling or a wet patch that keeps growing usually means the tank has corroded internally and is leaking through the base. Once the tank itself is leaking, it can't be repaired and needs replacing before it lets go completely and floods the area. We see this a lot on the older Aspley properties along Robinson Road West where systems have been sitting on damp ground for years without being checked.

I've got solar panels on my roof. Can I connect them to a hot water system?

If you've got solar PV panels generating electricity, pairing them with a heat pump hot water system is one of the best ways to use that excess power during the day instead of sending it back to the grid. The heat pump runs off the electricity your panels produce, so your hot water costs drop to almost nothing. A lot of Aspley homes have good roof orientation for solar, though the mature tree canopy around Downfall Creek and Marchant Park can cause shading issues on some properties. We'll check your setup and tell you if it's a good fit.

Why does my hot water smell like rotten eggs?

That sulphur smell is caused by bacteria reacting with the magnesium anode rod inside your tank. It's more common in areas with harder water and in systems that sit on a lower temperature setting. Replacing the magnesium anode with an aluminium one usually fixes the smell permanently. If the anode has completely dissolved and hasn't been replaced, the tank itself may be corroding unprotected, so it's worth getting it looked at sooner rather than later.

Can you install a hot water system in an Aspley townhouse or unit?

Yes. Aspley has a growing number of townhouses and unit complexes, particularly around Gayford Street, Aspley Village, and along Gympie Road heading toward Chermside. These properties often have limited outdoor space and specific body corporate requirements around equipment placement and noise. We install compact electric, gas instantaneous, and smaller heat pump units that suit tighter spaces and meet body corporate guidelines. We'll work with whatever access and restrictions your property has.

How long does it take to replace a hot water system?

A like for like swap where we're putting the same type of system back in the same spot typically takes two to three hours. If you're changing system types, for example going from electric storage to a heat pump or from a tank to instantaneous gas, it can take a bit longer because we need to run new connections or adjust the plumbing. Either way, you'll have hot water by the time we leave.

What brands do you install and recommend in Aspley?

We work with all the major brands including Rheem, Rinnai, Dux, Vulcan, Aquamax, and Reclaim for heat pumps. We don't push any single brand. What we recommend depends on your budget, your property setup, and what's going to perform best for your situation. We'll explain the differences between the options we're quoting so you can make an informed decision without being sold something you don't need.

Hot Water Systems Aspley

$0 Call Out Fee
24/7 Emergency Plumbing
After Hours & Weekends
Fast Response Time
$0 Upfront Payment Plans Available

📞 Call Now: 0482 979 551

Request Your Plumbing Service Today

Expert Plumbing Available 24/7

Fixed Upfront

Pricing

189+ 5-Star

Reviews

$0 Call-Out

Fees

24/7 Emergency

Service

$0 Upfront

Payment Plans

20-40 Minute

Response Time

Local & Reliable Hot Water System Plumbing in Aspley

We work on hot water systems in Aspley week in, week out. If yours has stopped heating, started leaking, or just can't keep up with the household anymore, our Aspley plumbers can be at your door the same day to sort it out. Weekend Plumbing Co. covers everything from emergency breakdowns through to full system upgrades.

Aspley's got a mix of older houses on bigger blocks and smaller units closer to the main roads. The older homes tend to have original systems that are well past retirement age, while the units often have undersized tanks that were never spec'd for how people actually use hot water. Either way, we'll look at what you've got, what your household needs, and give you a recommendation that makes sense for both the property and your budget.

One thing we see a lot in Aspley is reactive clay soil putting stress on plumbing infrastructure. Ground movement shifts pipe connections and can crack fittings around hot water systems, especially older installations sitting on concrete slabs that have moved over the years. It's worth knowing about because it affects how we install and position replacement systems to avoid the same problems down the track.

Hot Water Systems We Recommend for Aspley

We install every major system type. Here's what we find works best across different Aspley properties:

Electric Storage

Electric tanks are what we swap out most in Aspley. They suit the majority of homes here, they're affordable, reliable, and available in every size from 125L through to 400L. The current generation of electric tanks hold heat significantly better than older models, which means lower power bills without changing your habits. We supply Rheem, Dux, and Aquamax. Aspley's water is on the harder side, so we recommend periodic descaling to protect the element and keep the system running efficiently.

Gas

Gas heats quicker and runs cheaper over the long haul. Continuous flow units are the pick for bigger Aspley households because they never run dry. No tank, no waiting for a refill, just hot water whenever someone turns the tap on. They're also physically compact, which is handy in tighter setups. Gas storage tanks suit homes that prefer a traditional setup but want the running cost benefits of gas over electric.

Heat Pump

Heat pumps use ambient air temperature to heat water, pulling up to 70% less from the grid than a standard electric tank. Brisbane's climate keeps them performing well year-round. Aspley's older homes on larger blocks usually have plenty of room for the outdoor unit. Government rebates reduce the buy-in cost, and the electricity savings are noticeable from the first bill.

Solar

Solar uses roof-mounted collectors to heat water directly, cutting energy costs by 50 to 80%. A booster (electric or gas) covers overcast days so you're never without hot water. Aspley properties with unshaded, north-facing roof space get the strongest return. Upfront cost is higher than other options, but between government rebates and the ongoing savings, the investment pays for itself over time.

📞 0482 979 551

hot water system installation in Aspley home

How We Handle Hot Water Jobs in Aspley

Four steps from your call to hot water running properly again.

Site Visit and Assessment

We'll ask a few questions over the phone, then come out to your Aspley property to inspect the current system. We measure the install area, check if gas is available, and work out the right system size based on your household. If heat pump or solar is on the table, we assess roof orientation and outdoor space. We also look at ground conditions around the install location, because Aspley's reactive clay can affect how we position and secure the new unit.

Quote and Recommendations

We explain what suits your property and why, then give you a fixed price that covers the unit, installation, removal of the old system, and all fittings. No separate line items that creep up. We'll run through any government rebates you're eligible for and payment plan options if you'd prefer to spread the cost.

Installation

For standard electric and gas systems, we usually have stock on the van and can install the same day. The old unit gets pulled out, the replacement goes in to Australian standards, every connection is pressure tested, and we confirm hot water is flowing before we touch the cleanup. Most Aspley jobs wrap up in two to four hours.

Full Test and Handover

We run the system through a complete test cycle to check heating performance and confirm no leaks. We walk you through the temperature controls and show you the TPR valve so you know what's normal and what's not. Warranty gets registered with the manufacturer before we leave, and our installation work is backed by a lifetime workmanship guarantee.

Hot Water Breakdowns We Fix in Aspley

We're in and out of Aspley properties all the time. These are the hot water problems that fill our schedule.

Dead System, No Hot Water

First thing to check: has the circuit breaker tripped (electric) or has the pilot light gone out (gas)? If those are both fine and you're still getting cold water, something inside the unit has failed. Elements and burners wear out, and older systems have a habit of dying completely rather than giving you a gradual decline. We carry common replacement parts and can often get it diagnosed and repaired the same day. If the unit is too far gone, we'll tell you straight and talk through replacement options on the spot.

Tank Can't Keep Up

Cold water halfway through a shower is the classic sign. It's either a tank that's too small for the number of people using it, or sediment eating into the usable volume inside the tank. Aspley's hard water and reactive clay soils compound the problem. Mineral scale builds up faster in harder water, and ground movement can stress fittings and connections, letting sediment settle in spots it wouldn't normally reach. We can flush the tank, but if it's genuinely undersized, we'll recommend stepping up to something that matches the household.

Unsafe or Unpredictable Temperatures

Water that comes out scalding or jumps between hot and cold is a thermostat or tempering valve problem. Both are straightforward fixes for us. We'll test the components, replace whatever's faulty, and make sure the output temperature is safe and consistent before we leave.

Leaking Tank or Connections

A leak from a valve or pipe fitting can usually be repaired. A leak from the tank itself means corrosion has eaten through the steel, and that's a replacement. Aspley's combination of hard water and humidity accelerates corrosion on older tanks. Ground movement from the clay underneath can also pull pipe joints apart over time, creating slow leaks that go unnoticed until water starts pooling. If you see water around the base of your unit, call us before it gets worse.

Noisy Tank

Popping, rumbling, or crackling when the system heats up is sediment bouncing around at the bottom of the tank. It means the element is working through a layer of mineral buildup to heat the water, using more energy and wearing the tank out faster. A flush clears it and restores normal operation. Systems that haven't been serviced in years often have a significant sediment layer by the time we get to them.

Signs Your System Needs Looking At

These are the things we tell Aspley homeowners not to ignore:

Slow to heat: Noticeably longer than it used to take
Discoloured hot water: Brown, orange, or rusty water means internal corrosion
Electricity bill jumped: A failing system pulls more power to do the same job
Pilot light keeps dying (gas): Thermocouple or gas valve on the way out
Breaker trips when it runs (electric): Faulty element or wiring issue
Weak flow from hot taps only: Something inside the system is restricting water

If any of that sounds like your system, call us on 0482 979 551. Dealing with it now is always cheaper than a full failure. We're on call 24/7 for hot water emergencies.

Fix It or Replace It?

Here's how we help Aspley homeowners make the call:

How Much Life Is Left?

A hot water system that's past the 10 to 15 year mark is running on borrowed time. Parts get scarce, efficiency deteriorates, and the odds of another failure shortly after a repair go up with every year. If the system is in that territory, the money spent on a repair is often better invested in a new unit with full warranty coverage and modern efficiency.

Have We Been Here Before?

If it's the second or third callout in recent memory, the system is winding down. The rule of thumb we use: once repairs add up to roughly half the cost of a new system, it's time to stop patching and start fresh.

What's Your Power Bill Doing?

A system losing efficiency doesn't announce itself. It just quietly costs you more every quarter. Modern replacements use 20 to 50% less energy, and that difference compounds fast. A new electric tank or heat pump can pay back the upgrade cost through lower bills within a few years.

Right-Sizing Your New System

Too small and you're back to running out of hot water. Too big and you're heating water that sits there unused. We size to the people in the house and how they use hot water, not the size of the property. Here's our guide for Aspley households:

Household Size	System Type	Recommended Size	Perfect For
1-2 People (Smaller Households)	Electric Storage	125L-160L tank	Units near Aspley Village Shopping Centre, apartments throughout the retail precinct, or couples in smaller homes in Aspley's established residential areas and near Downfall Creek Reserve.
	Gas Storage	135L-170L tank
	Instant Gas	16L-20L per minute
3-4 People (Average Family)	Electric Storage	250L-315L tank	Most Aspley family homes throughout the suburb, properties along tree-lined residential streets, homes near Downfall Creek Reserve walking trails, and properties near Aspley Village Shopping Centre and Aspley Hornets sporting grounds.
	Gas Storage	135L-170L tank (heats faster)
	Instant Gas	20L-27L per minute
	Heat Pump	250L-315L tank
5+ People (Large Families)	Electric Storage	315L-400L tank	Larger Aspley homes throughout the suburb, multi-generational properties, family residences with high hot water demand, and homes near Aspley State School and community facilities requiring sustained hot water supply.
	Gas Storage	170L tank with booster
	Instant Gas	27L+ per minute
	Heat Pump	315L-400L tank

If you're not sure what size your household needs? We'll help you choose the right system based on your household size, bathroom count, and actual usage patterns. Call us for an assessment at 0482 979 551 .

installing a gas hot water system in Aspley

Why Choose Weekend Plumbing Co. For Your Hot Water Plumbing

We assess the job, give you a fixed number, and that's what you pay. Nothing gets added once we start work. No callout fee either.

Included as standard with our service:

$0 callout fee
System assessment and sizing advice
Fixed quote before any work begins
Same-day install on standard systems
Old unit removed and disposed of
Pressure and leak tested before we leave
Manufacturer warranty registered
Lifetime workmanship guarantee
Rebate and payment plan assistance

Why Aspley Homeowners Call Weekend Plumbing Co.

We're in Aspley regularly. We know the housing, we know the soil, and we know what hot water systems hold up best here.

What Makes the Difference

Based in Albany Creek: A few minutes away, so we get to Aspley fast
We understand this suburb: Hard water, reactive clay, older plumbing. We deal with it every week and plan our installs around it
Same-day replacement: Common systems carried on the van for immediate install
Work with all system types: Electric, gas, heat pump and solar
Honest about repair vs replace: We'll tell you which option saves you money long term
Rebates handled: We sort the paperwork and make sure you claim what's available
$0 upfront payment plans: Get the new system now and pay it off over time

Call us on 0482 979 551 to book. Same-day appointments available, and for emergencies we can usually be at your Aspley property within the hour.

📞 0482 979 551

Need a Reliable Hot Water Plumber in Aspley?

Call now for fast and reliable hot water system service. We're your local Brisbane plumbers, based near Aspley and available 24/7 for emergencies.

📞 0482 979 551

Frequently Asked Questions

Hot Water Systems Aspley FAQs

It can be. A small amount of water from the pressure relief valve is normal during heating cycles, but steady pooling or a wet patch that keeps growing usually means the tank has corroded internally and is leaking through the base. Once the tank itself is leaking, it can't be repaired and needs replacing before it lets go completely and floods the area. We see this a lot on the older Aspley properties along Robinson Road West where systems have been sitting on damp ground for years without being checked.
If you've got solar PV panels generating electricity, pairing them with a heat pump hot water system is one of the best ways to use that excess power during the day instead of sending it back to the grid. The heat pump runs off the electricity your panels produce, so your hot water costs drop to almost nothing. A lot of Aspley homes have good roof orientation for solar, though the mature tree canopy around Downfall Creek and Marchant Park can cause shading issues on some properties. We'll check your setup and tell you if it's a good fit.
That sulphur smell is caused by bacteria reacting with the magnesium anode rod inside your tank. It's more common in areas with harder water and in systems that sit on a lower temperature setting. Replacing the magnesium anode with an aluminium one usually fixes the smell permanently. If the anode has completely dissolved and hasn't been replaced, the tank itself may be corroding unprotected, so it's worth getting it looked at sooner rather than later.
Yes. Aspley has a growing number of townhouses and unit complexes, particularly around Gayford Street, Aspley Village, and along Gympie Road heading toward Chermside. These properties often have limited outdoor space and specific body corporate requirements around equipment placement and noise. We install compact electric, gas instantaneous, and smaller heat pump units that suit tighter spaces and meet body corporate guidelines. We'll work with whatever access and restrictions your property has.
A like for like swap where we're putting the same type of system back in the same spot typically takes two to three hours. If you're changing system types, for example going from electric storage to a heat pump or from a tank to instantaneous gas, it can take a bit longer because we need to run new connections or adjust the plumbing. Either way, you'll have hot water by the time we leave.
We work with all the major brands including Rheem, Rinnai, Dux, Vulcan, Aquamax, and Reclaim for heat pumps. We don't push any single brand. What we recommend depends on your budget, your property setup, and what's going to perform best for your situation. We'll explain the differences between the options we're quoting so you can make an informed decision without being sold something you don't need.